Helmet Guides

T-CLOCS Pre-Ride Inspection: A Motorcycle Checklist You Can Do in 5 Minutes

Black full-face helmet with a tinted visor resting on a motorcycle before a pre-ride check

About this guide: This article is general motorcycle helmet advice from the CYRIL Helmets team. Any helmet problems it mentions are common to helmets of all brands and are not reports of defects or complaints about a specific CYRIL model. All current CYRIL helmets are certified to U.S. DOT FMVSS No. 218. For help with your own CYRIL helmet, contact our customer service team.

T-CLOCS is the pre-ride inspection checklist from the Motorcycle Safety Foundation (MSF). The letters stand for Tires and wheels, Controls, Lights and electrics, Oil and other fluids, Chassis and Stands. A quick walk-around takes about five minutes and catches the problems that most often leave riders stranded or cause a loss of control: low tire pressure, a loose chain, a dead brake light or a leak. Below is what to check in each step, how often, and a 30-second helmet check to add at the end.

Rider in a gray open-face helmet sitting on a motorcycle

T-CLOCS at a glance

Letter Area Quick check
T Tires and wheels Pressure, tread, damage, spokes or rims, bearings
C Controls Levers, pedals, cables, hoses, throttle
L Lights and electrics Headlight, brake light, turn signals, horn, battery
O Oil and other fluids Engine oil, brake fluid, coolant, fuel, leaks
C Chassis Frame, suspension, chain or belt, fasteners
S Stands Side stand and center stand, springs, cut-out switch

You do not need to do every item in full detail before every ride. A sensible routine is a quick version daily (pressure, lights, brakes, leaks, chain) and the full list weekly or before a long trip. Your owner's manual gives the exact specs and intervals for your bike.

T: Tires and wheels

  • Pressure. Check it cold, before riding, with a gauge. Use the pressures in your owner's manual or on the label on the swingarm or chain guard, not the maximum printed on the tire sidewall.
  • Tread. Look for the wear bars in the grooves. If the tread is level with them, the tire needs replacing. Check for flat spots in the center, which reduce grip when leaned over.
  • Damage. Run your eyes and hand around each tire for nails, cuts, bulges and cracking in the sidewall.
  • Age. The last four digits of the DOT code on the sidewall show the week and year the tire was made. Old rubber hardens even with plenty of tread left.
  • Wheels. Look for dents or cracks in cast rims and loose or broken spokes. With the wheel off the ground, check that it spins freely and has no play in the bearings.

C: Controls

  • Levers and pedals. Clutch, front brake lever, rear brake pedal and shifter should move smoothly, return on their own and not be bent or cracked.
  • Cables. No fraying or kinks. Turn the bars lock to lock and make sure the cables do not pull tight or snag.
  • Hoses. Brake hoses should be free of cracks, bulges and leaks at the fittings.
  • Throttle. It should snap back closed when released, in every steering position. A sticky throttle is a reason not to ride.

Rider in a black open-face helmet beside a motorcycle by a red wall

L: Lights and electrics

  • Headlight. Low and high beam both work and the beam is not aimed too high or too low.
  • Brake light. Test it with the front lever and the rear pedal separately. Each should light it on its own.
  • Turn signals and horn. All four indicators flash at a normal rate. Press the horn.
  • Battery and wiring. Terminals are tight and free of corrosion. Wires are not rubbing or pinched.

Lights are how drivers see you, especially at dawn and dusk. If you ride at night often, our guide to night riding visibility covers the helmet and visor side.

O: Oil and other fluids

  • Engine oil. Check the level with the bike upright on level ground, using the sight glass or dipstick as your manual describes.
  • Brake fluid. The level sits between the marks in each reservoir. Dark fluid is due for a change.
  • Coolant. On liquid-cooled bikes, check the overflow tank level with the engine cold.
  • Fuel. Enough for the ride, and no smell of fuel or wet spots around the tank and lines.
  • Leaks. Look under the bike where it was parked. Fresh drips of oil, coolant or brake fluid need finding before you ride.

C: Chassis

  • Frame. Look for cracks, bends or damage, especially after a drop.
  • Suspension. Push down on the front and rear. It should compress smoothly and return without bouncing. Check the fork seals for oil.
  • Chain or belt. Check slack against the spec in your manual, and look for tight spots, rust or worn sprocket teeth. A belt should be free of cracks and missing teeth.
  • Fasteners. Axle nuts, mirror mounts and anything you have recently worked on should be tight.

S: Stands

  • The side stand and center stand should not be cracked or bent.
  • Springs should pull the stand up firmly. A stand that drops while riding can catch the ground in a left turn.
  • If your bike has a side-stand cut-out switch, check that the engine stops when you put it in gear with the stand down.

Black and white full-face helmet with a dark visor on a bike

Add a 30-second helmet check

T-CLOCS covers the motorcycle, but your helmet is part of the ride too. Before you set off:

  • Shell. No cracks, deep gouges or dents. If the helmet has been dropped hard or crashed, read what to check after a drop.
  • Strap. Buckle and rivets are solid, and the strap is snug with no more than about two fingers under your chin.
  • Visor. Clean, free of deep scratches, and it opens and locks properly.
  • Fit. The helmet does not rotate or slide when you shake your head.

Our full 60-second helmet check walks through each step, and the beginner gear checklist covers the rest of your riding kit.

FAQ

What does T-CLOCS stand for?

Tires and wheels, Controls, Lights and electrics, Oil and other fluids, Chassis, and Stands. It is the pre-ride inspection checklist published by the Motorcycle Safety Foundation.

How often should I do a T-CLOCS inspection?

Do a short version before every ride (tire pressure, lights, brakes, leaks, chain) and the full checklist weekly, after the bike has been stored, and before any long trip.

How long does a T-CLOCS check take?

About five minutes once you know your bike. The first few times may take 15 minutes while you learn where everything is.

Is T-CLOCS part of the motorcycle license test?

The MSF Basic RiderCourse teaches it, and many state rider manuals include a pre-ride inspection section. Some skills tests ask you to show basic checks. Here is what to bring to an MSF course.

What should I do if something fails the check?

Do not ride until it is fixed. Low tire pressure or a loose mirror is a quick fix at home. Brake, throttle, steering or tire damage problems should go to a qualified mechanic.

Sources